Catálogo general de máquinas para la madera (inglés)

98 99 EB25 A CantSpray EB35 For panel edgebanding with pre- glued PVC, melamine and veneer. Automatic edge feeding system. Trimming on both sides. Motorized top and bottom trimming unit. Front edge trimming, rear flush cutting of the tape. No compressed air or dust collector required. Powerful hot air system with electronic temperature control. Minimum heat up time (2 min). Belt feeder for automatic workpiece. Safety control (STOP). Electronic temperature control. Standard equipment AK97N Motorized trimming unit AQ10 Belt feeder Table extension End cutting of front and back of the tape. Specifications Input power 3,000 W Min. panel thickness 11 mm Max. panel thickness 50 mm Electronic temp. control 0°-500°C Working speed 4.2 m/min Dimensions 1,720x950x1.350 mm Weight 117 kg Non-adherent without silicone for all movable parts on the edgebanding machines (trimming blades, end cutting blades). Optional accessories 6399082 Cantspray A Power trimming unit: trimming both sides simultaneously. Feed unit: feeding of the workpiece to be edged. Edgebanders Edgebander Single phase 220-240 V. No com- pressed air required. Edgebanders Specially designed for banding preglued PVC, polyester, melamine and veneer tapes. Possibility to band and trim tapes up to 3 mm thick. Belt feeder for automatic workpiece feeding. Top and bottom trimming by two independant motorized trimming units, equipped with TCT bits; possibility to trim with radius or straight edges. Scrapper unit and automatic tape feeding system. Front and rear flush cutting of the tape (for tapes up to 2 mm thick). Minimum heat up time. Electronic temperature control. Minimal, easy maintenance. Large surface table with special guides. Automatic workpiece feeding. Front and rear flush cutting (tapes up to 2 mm thickness only). Simultaneous top and bottom trimming, with radius or 10° chanfer. Flat scrappers after the trimming unit. Standard equipment Belt feeder unit Motorized top and bottom trim- ming unit with TCT bits r=3+10° chanfer Scrapper unit Front and rear flush cutting Table extension Single phase 220-240 V. No com- pressed air required. Specifications Input power 4,000 W Min. panel thickness 13 mm Max. panel thickness 1 mm tape 50 mm Max. panel thickness 2 mm tape 35 mm Max. panel thickness 3 mm tape 25 mm Min. panel width 102 mm Min. panel length 110 mm To ensure the tape is well banded, the EB35 incorporates two auxiliary rollers on the banding table and a special pressers set, allowing the optimum pressure of the panel on the banding unit. This ensures a co- rrect banding, specially when using thick and rigide tapes. The EB35 is also equipped with a selection lever to regulate the correct work- piece position depending the tape thickness. A heating unit «Leister» with electronic regulation, from 0° to 500°, is ensuring a correct banding temperature for any kind of tapes. Electronic temp.control 0°-500°C Working speed 4 m/min Trimming unit no-load speed 10,000/min TCT bits Ø 59, Z4, R3, +10° Voltage (single phase) 220-240 V Dimensions 1,720x950x1,350 mm Weight 135 kg Edgebander Optional accesories 8200300 AS382L Dust collector, equipped with two motors and prepared to work during the trimming cicles automatically 8545498 For general dust collec- tion systems with a minimum ca- pacity of 1000 m3/h. Attachment with connectors Ø ext. 38-100 mm 6399082 Cantspray. Non-adhe- rent without silicone (see page 98) PR25P Pregluers (see pages 101) Optional bits Carbide bit r=3+10° (included as standard equipment) Carbide bit r=2+10° Carbide bit 45°