Catálogo general de máquinas para la madera (inglés)

56 57 FC116U A B UC16K Specially designed for quick, pre- cise mortising on doors or other elements, either at the work site or in the workshop. Its special fixing system allows the mortising of doors that have already been hung, without damaging the surface. Its quick measurement adjustment permits multiple mortises to be made in record time. Possibility to trim the frontal lock plate just changing the bit. Equipped as standard with the accessory UT16I which allows to take references for drilling the hole for the handle and key cylinder. Also able to work horizontally. For mortising grooved doors or those with overlap, there is an adjustment system to cen- tre the machine. Optional bits are low cost and easily interchangeable, as they use the same tool-holding shaft. The machine is also able to work horizontally. Especially useful if deciding to make a series of mor- tises, with the doors unhung. Wooden box for carriage. Ideal for making lock mortises. It also permits to mortise grooved doors or those with overlap, thanks to the possi- bility of adjusting the centre of the machine over the section of the door where the mortise is required. Standard equipment Equipped from factory with carbide lock mortiser bit Ø 16 mm, locking bar to make mortises on several doors at the same height, rubber protectors for delicate jobs, service keys, dust collector connection and UT16I drilling accessory. Specifications Input power 1,100 W Max. bit Ø 30 mm No-load speed 23,000/min Max. mortising depth 0-125 mm Max. mortising length 177 mm+bit Ø Max. clamp vise opening 190 mm The FC116U incorporates a locking bar, which is fixed to the machine at the height from the ground established for the first mortised door, allowing the mortising of the rest of the doors at the same height without retaking measurements. Mount any lock with the FC116U Lock mortiser Installation and restoration of doors and windows Optional accessories 1645287 UP16I Clamp extension 1645288 UT16I Drilling accessory 1640148 Carb. drilling bit* 2 c. Ø 18 mm 1640149 Carb. drilling bit* 2 c. Ø 23 mm (*) For using with a drill A B The clamp extension UP16I allows to fix the machine also on both ends of the door. The accessory UT16I allows to take references for drilling the hole for the handle and key cylinder. Making side holes for placing the knob, cylinder or other mechanisms. Using UC16K together with FR66P enables the user to quickly make recesses of exceptionally high quality. UC16K gives extraordinary results on frames too. Using UC16K with the FR66P enables the user to make recesses for the box-staple or lock and the holes for the latch and lever Standard equipment Set of templates, template guide for (FR66P /FR160P) and service keys. Additional sets may be ordered separately (ref. 1645365) Specifications Work area on door front: 80 x 300 mm. Work area on door edge: 55 x 300 mm . Maximum opening of clamp vises: 190 mm. Maximum grip of clamp vises: 13 mm. Maximum trimming depth: 60 mm. The UC16K is necessary when placing magnetic card locks, anti-panic locks and other special kind of locks. Lock mortising template holder Optional bits Sharing the same tool-holding shaft. Easily interchangeable. 1640138 Set of 5 carbide bits Diameters: 18, 21, 23, 25, 30 mm (ref. 1640138) (*) Bit included with standard equipement. Tool-holding shaft included with the FC116U 1640127 Carbide bit Ø 16 mm* 1640150 Carbide bit Ø 17 mm 1640128 Carbide bit Ø 18 mm 1640367 Carbide bit Ø 20 mm 1640129 Carbide bit Ø 21 mm 1640378 Carbide bit Ø 22 mm 1640130 Carbide bit Ø 23 mm 1640368 Carbide bit Ø 23.5 mm 1640131 Carbide bit Ø 25 mm 1640369 Carbide bit Ø 29 mm 1640132 Carbide bit Ø 30 mm 1640140 Drilling bit UC16K is designed for making frontal and lateral recesses for any kind of lock on doors and frames. Designed for use with the router FR66P or FR160P, it is especially recommended for making recesses for locks that open with mag- netic anti-panic cards and special opening devices. Its exclusive attachment system by means of clamp vises enables the user to mortise doors that have already been hung without damaging the surface. Se- cure, reliable grip. Works horizontally also. UC16K includes a height bar, making possible identical recesses on several doors at the same height, with no need to readjust the lock mortising template holder. Optional bits 1640157 Carbide bit Ø 12 mm (for FR66P) 1640258 Carbide bit Ø 12 mm (for FR160P) (see page 39) Installation and restoration of doors and windows