Premarcos abrazamuros (inglés)

Hinge side Hinges Hinge side 13 14 15 Screw Ø 6.3x60 mm DIN 7504P Horizontal level Vertical level Corner fit Corner fit If the assembly instructions have been followed closely, the following slacks shall be observed: Turia-Delta DH Turia Slack between leaf & frame on the hinge side. 4 mm (± 3 mm) 4 mm (± 3 mm) Slack between leaf & dintel. 3 mm (± 3 mm) 3 mm (± 3 mm) Slack between leaf & frame on the lock side. 5 mm (± 3 mm) - Slack between leaf & floor. 7 mm (± 3 mm) 7 mm (± 3 mm) Slack between leaves. 7 mm (± 3 mm) 16 Introduce the doorset into the sub-frame. Place it correctly according to the following figure. Open the leaf or remove it, to screw the frame onto the sub-frame with selftapping screws Ø 6,3x60 mm (¼ x 2”) DIN 7504P. It will bear 4 screws on each side jamb, whose position are marked by the bores on the frame. Level the frame vertically and horizontally. Remove the expanding joint (intumescent seal) from the frame and drill into the four bores of the frame to the sub-frame with a hand drill of Ø 5,25 mm (3/16”). Next attach the frame onto the sub-frame and put-back the expanding joint. Remove the corner fittings, unscrew the girder, tear off the tab on the nylon lock protector and close the leaf. Install the door handles and the door-closer according to the instructions attached to the doorset. Remove the expanding joint Tab of the lock protector Bottom rod bush Only Double Leaf Doors. VERY IMPORTANT: Install the bottom rod bush on the floor to fit the bottom rod and prevent door warping. Hinge side Hinge side 6 U-Shaped profile Sub-frame Plasterboard liner 15 mm Screws Ø 3,9x25mm Screw Ø3.9x25 mm Transom Metal Structure Plasterboard liner of 15 mm 7 U-Shaped profile Sub-frame Screw Ø 3.9x45 mm Screw Ø 3.9x25 mm Rockwool Transom Rockwool 8 1 U-Shaped lenghtener U-Shaped top leg U-Shaped top leg Screws aut. Ø 4.2 x 13 mm. 7504N 2 Horizontal Level Vertical level 5 . 6 3 0 3 U-Shaped profile Sub-frame 0 3 Self tapping Screw Ø 4.2x13 FST 48 mm U-Shaped profile 3 4 5 Bottom anchoring square Top anchoring square Screw Ø 3.9x45 mm Screw Ø 3.9x25 mm Gunning paste Sub-frame Plasterboard sheets of 15 mm Gunning paste 9 10 1 Leaf Double Leaf 11 Anchor grip Anchor bush 12 Cut off the U-Shaped lengthener to fit the Top Anchoring Square to the ceiling. Screw the U-Shaped lengthener to the Top U-Shaped Legs of the sub-frame with two Sheet metal screw Ø 4,2x13 mm ( 1/6 x ½”) DIN 7504N. Drive the sub-frame to the wall with the U-Shaped lengtheners fastened and level it both vertically and horizontally. Next, bring the U-Shaped profiles of 48 mm (1 7/8”) to the sides and top of the sub-frame and screw them to it using 7 screws on each side jamb and 5 on the lintel, use Sheet metal screws Ø 4,2x13 mm ( 1/6 x ½”) FST. Note: To allow the sub-frame to fit into the lintel, the U-Shaped profiles must be placed with a slack of 30 mm (1 1/6”) on each side taken from the cross-section of the sub-frame. Screw or fix the Top & the Bottom Anchoring Squares of the sub-frame to the ceiling and the floor accordingly using the recommended screws Ø 4,8x32 mm (3/16x1¼) DIN 798. Introduce the anchor-bush into the anchor-grip. Mind the position and path according to the figure below. Once the wall is dry, remove the girders and the corner fittings from the sub-frame. Seal the junction between the plasterboard and the sub-frame with gunning paste, cover the holes of the screw heads, etc. Cover the junctions between plates with paper and gunning paste. Place the other face of plasterboard liner. Introduce a layer of rock wool 23 mm ( 7/8”) between the U-Shaped profiles & the transoms. Place one side of the plasterboard liner wall on the metal rack. Use two layers of plasteboard (or similar) 15 mm (5/8”) thick and self tapping screws Ø 3,9x25 mm (5/32 x 1”) & Ø 3,9x45 mm (5/32 x 1¾”).. Fix the 48 mm (7/8”) U-Shaped profiles to the ceiling and the floor, then place the 46 mm vertical transoms . We recommend to use self tapping screws Ø 3,9x25 mm (5/32 x 1”). Rivet the transoms and the profiles. Top square ceiling anchoring 46 mm U-Shaped transom Screw Ø 4.8x32 mm DIN 7981 ¡¡ Recommended !! Screw Ø 4.8x32 mm DIN 7981 ¡¡ Recommended !! Horizontal Level Installation in Flexible Wall (Plasterboard) Self tapping Screw Ø 4.2x13 mm FST Leaf 10 1 1 9 5 3 4 6 7 11 8 2 1 . Plasterboad panels. 2 . Rockwool (Mineral rockfibre). 3 . Steel Galvanised sub-frame. 4 . Steel Galvanised CS5 frame. 5 . U-Shaped profile. 6 . Sheet metal screw Ø 4,2x13 mm (1/6x ½”) extra flat head or DIN 7504N. 7 . Sheet metal screw Ø 6,3x60 mm (¼ x 2”) DIN 7504P. 8 . Graphite intumescent joint (Fire Prevention). 9 . U-Shaped Vertical Transom. 10. Self tapping screw Ø 3,9x45 mm (5/32 x 1¾”). 11. Self tapping screw Ø 3,9x25 mm (5/32 x 1”). FINISHES White Galvanised Antifinguer Stainless Steel On Plaster Board Wall www.baygar.com